Best Cabinet Handles in Australia (2026)

Why new cabinet handles are the cheapest room makeover in the house

Because a full set costs less than a run of splashback tiles, and swapping them changes how the whole kitchen reads. We did this in our own first place: builder grade doors, chalky chrome D pulls, a budget already eaten by the removalists. Two hours with a screwdriver did more than any amount of scrubbing.

The catch is that the pretty photo tells you almost nothing. What decides whether the job takes twenty minutes or a wasted Saturday is one number: the hole centre spacing, measured from the middle of one screw hole to the middle of the other. Get it wrong and you are filling and redrilling doors.

This guide covers eight cabinet handle multi packs on Amazon Australia, across bar pulls, cup pulls, knobs and edge pulls, with hole centres, pack sizes and finishes taken from each listing. It is written for retrofitting a kitchen or a laundry run of cupboards, and it covers cabinetry pulls and knobs only, not the lever sets on your interior doors. For drawer inserts rather than hardware, our drawer organiser guide is the sibling page.

The short answer on cabinet handles

For most kitchens the Franklin Brass Francisco 10 pack in champagne bronze is the dependable all rounder: 128mm hole centres, a slim 18mm projection that is far less likely to catch a hip pocket, and a limited lifetime warranty stated on the listing. It is also the most reviewed product in this guide by a clear margin, which matters when you buy ten identical items sight unseen.

If your doors are white, grey or timber and you want the standard contemporary look, the Fiabgum matte black 128mm 10 pack is the value option: stainless steel rather than zinc, the same 128mm centres, and a chunkier 35mm projection that suits deep pot drawers.

On a tight budget, or if the laundry and linen press need doing too, the Qrity aluminium 64mm 10 pack is the cheapest of our eight picks and still carries several hundred ratings. It is short, so it belongs on cupboard doors and narrow drawers rather than a 900mm pan drawer.

Beyond those three we picked a bin cup pull for Shaker kitchens, oval knobs for bedroom furniture, brass edge pulls for a near handleless look, knurled brass, and a heavy square bar.

Cabinet handles compared at a glance

Hole centre spacing is the column to read first.

How we evaluated cabinet handles

• Hole centres and overall length were read off each Australian listing and converted to millimetres, since that decides whether a handle fits your existing holes.
• Pack size was weighed against price per handle, since a kitchen swap needs roughly 15 to 25 pieces and a four piece pack rarely finishes it.
• Ratings and review counts were pulled fresh on the day this guide was written, and we noted where a pick has a smaller review base than the others.
• We spread the shortlist across bar pulls, cup pulls, knobs and edge pulls, so it answers a style question as well as a size one.

Best cabinet handles overall: Franklin Brass Francisco 10 pack

This is the set we would put on a whole kitchen without thinking twice. Ten identical bar pulls with 128mm hole centres, about 152mm long, and a projection of roughly 18mm, slim enough to matter in a narrow galley: at 18mm off the door face it is far less likely to hook a tea towel or a jeans pocket than the deeper bars below.

The finish is champagne bronze, brushed rather than polished, the modern middle ground between gold and stainless: warm enough to lift a white Shaker door, neutral enough to sit beside stainless appliances. The body is aluminium on a zinc mounting at about 35 grams a handle, and the listing states a limited lifetime warranty from the manufacturer, the only pick in this guide whose listing carries a warranty line.

With 4.7 stars from more than two thousand ratings it is the most reviewed product on this list by a clear margin. When you buy ten of something at once that volume matters, because the failure mode with cheap handles is variation between pieces in the same pack rather than outright breakage.

Flaws but not dealbreakers

The 128mm centres are fixed, so this is not the set for a kitchen still wearing 96mm hardware unless you will fill and redrill. Champagne bronze also photographs warmer than it looks in a south facing kitchen, so hold one pack against your tapware before ordering the second.

Best matte black cabinet handles: Fiabgum 128mm 10 pack

Matte black is still the default request in Australian kitchen renovations, and this is the version we would buy. Ten T shaped bar pulls, 128mm hole centres, stainless steel rather than the zinc alloy most hardware uses at this price, and a matte black finish over a brushed base.

Stainless matters more than it sounds. Zinc alloy is cast, which gives crisper detail but a softer core, and the plating is what you rely on. Stainless puts a harder base metal under the black, so a chipped corner shows silver rather than grey pot metal. In a family kitchen where the pan drawer takes a knee daily, that is more forgiving.

The 35mm projection is close to double the Franklin Brass set, a design choice rather than a fault. A deep bar is easier to hook with wet hands and gives leverage on a heavy drawer, though on upper cupboards in a tight kitchen it is the wrong call, so many people mix: deeper pulls low, flatter high. It holds 4.6 stars from the smallest review base in this guide.

Flaws but not dealbreakers

Matte black is the least forgiving finish for fingerprints and cooking oil, so a handle above a cooktop needs wiping often. The listing also mixes nickel and matte black wording in its finish description, so treat the photos as the guide. Ten handles will not finish an average kitchen.

Best budget cabinet handles: Qrity aluminium 64mm 10 pack

Working through a whole house rather than one kitchen, this is the cheapest of our eight picks and the set we would use on a laundry, linen press or garage cupboard run. Ten aluminium handles, 64mm hole centres, a plain rectangular profile in silver.

The 64mm spacing is the important detail. Plenty of Australian flat pack kitchens, IKEA units and older 1990s cupboards were drilled at 64mm, so a short handle like this is the one most likely to drop onto existing holes without filling.

Aluminium keeps the price down and the handle light, which is fine on a cupboard door and less ideal on a heavy drawer. It also means the finish is the metal itself rather than a coating, so there is nothing to flake. It carries 4.5 stars from more than five hundred ratings. Pair it with a driver from our cordless drill guide if you are doing more than a dozen.

Flaws but not dealbreakers

At 64mm centres this is a small handle and it looks undersized on anything wider than about 400mm. Aluminium dents if you drop a pot on it, where zinc or stainless would shrug it off. The silver finish is a plain machine look, which is why it suits utility spaces more than a feature kitchen.

Best cup pulls for a Shaker or Hamptons kitchen: Hestia Hardware bin cup 10 pack

Cup pulls turn a plain Shaker drawer into a Hamptons drawer, and this is the only cup pull in our shortlist. Ten satin nickel bin cups, 64mm hole centres, about 103mm wide overall, cast in zinc at 36 grams each.

Cup pulls read as traditional because of how your hand meets them. You reach under rather than around, which suits a drawer front and looks wrong on a hinged door, so the classic layout is cup pulls on the drawers and knobs on the doors.

Satin nickel is the forgiving finish here: warmer than chrome, cooler than brass, and better than either at hiding water marks on a drawer under a sink. It holds 4.7 stars from over five hundred ratings. Zinc casting gives the cup its crisp arched profile, and since you only hold the front lip, casting quality shows up as whether that edge feels rolled or sharp.

Flaws but not dealbreakers

Cup pulls collect dust and crumbs under the bowl, the trade for the look. The 64mm centres make this a small cup, right on a 400mm to 600mm drawer and lost on a wide pan drawer, where a 96mm or larger cup belongs. Ten pieces covers a drawer bank, not a kitchen.

Best cabinet knobs for a dresser or vanity: BEILEIOU oval antique brass 5 pack

Knobs are the answer when a piece of furniture is too pretty for a bar pull. Five oval knobs, roughly 34mm by 36mm across the face, projecting about 34mm, cast in zinc alloy with an antique brass finish.

A knob mounts on a single screw rather than a pair, which changes the retrofit maths completely. There is no hole centre spacing to match, so a knob fits any door or drawer that already has one hole in it, and it is the easiest choice when you cannot get a clean measurement off the old hardware.

The antique brass is a genuinely aged tone rather than bright polished gold, so it works on dark timber and heritage paint colours, and on a white vanity it reads as a deliberate vintage detail. At 4.6 stars from over a hundred ratings it is well liked without the review volume of the bar pull sets. Five knobs suits one dresser or vanity, so count your hinged doors before ordering.

Flaws but not dealbreakers

An oval knob has a right way up, so mount them all with the long axis the same way or the eye picks up the inconsistency. Antique finishes also vary slightly piece to piece by design, which is charming on a dresser and less so if you expected uniformity. Knobs give less grip than a pull on a heavy drawer.

Best handles for a near handleless kitchen: RZDEAL solid brass edge pulls

If you like the handleless look but your doors are not routed for a J pull, edge pulls are the retrofit. Four solid brass pulls, each about 61mm long, 45mm wide and 21mm high, in a brushed gold finish, mounted at 40mm centres.

An edge pull screws onto the door face near the top or side edge and gives you a lip to hook rather than a bar to grip. Straight on, the door reads almost as a plain slab. On a run of tall pantry doors that is a genuinely different look to a row of bar pulls, and it is the cheapest way to get near it without new joinery.

Solid brass, not brass plated zinc, is why this one made the list. Each pull weighs about 50 grams for its size, and solid brass ages by developing patina rather than shedding a coating. Tied with the KOOFIZO square bar at 4.8 stars, it is one of the two highest rated picks here. Four pieces is often right, since edge pulls usually go on a limited run such as a pantry, an island end or a bank of laundry doors.

Flaws but not dealbreakers

Edge pulls need clearance above or beside the door, so they do not suit a door sitting hard against a wall or bulkhead. Brushed solid brass also changes tone over a few years unless you polish it, a feature to some people and a defect to others.

Best knurled brass handles: POVEFONK 128mm 10 pack

Knurled brass is the finish doing the rounds in Australian kitchen photography right now, and this set gives you ten at once. Bar pulls with 128mm hole centres, about 157mm long, a 33mm projection, and a brushed brass finish over an aluminium body.

Knurling is the diamond crosshatch machined into the grip. It is not decoration alone: the texture gives your fingers something to bite on when your hands are wet or oily, which is the argument for a kitchen rather than a bedroom.

This is the dearest of our eight picks, and the pack of ten is the reason. It holds 4.5 stars from over a hundred and fifty ratings, at the lower end of our shortlist but inside the same narrow band as the Qrity set. Brushed brass on aluminium keeps each handle to about 70 grams.

Flaws but not dealbreakers

The brass here is plated over aluminium rather than solid, so it will not patina and can wear through at the highest contact point over years. Knurled texture traps grease in the grooves and needs a soft brush rather than a wipe. The 128mm centres rule out a straight swap on 96mm cabinetry.

Best square bar handles: KOOFIZO solid square bar 10 pack

Rounded bar pulls soften a kitchen; square ones sharpen it. Ten square bars at 128mm hole centres in an oil rubbed bronze finish, cast in zinc alloy at about 90 grams a piece.

Weight is the giveaway with square bars. A hollow tube handle rings when you tap it and flexes if you pull hard on a full drawer; a solid cast bar does neither.

Oil rubbed bronze is a dark brown black rather than a true black, with warm highlights where the finish is worked back. It suits timber doors, deep green and navy cabinetry, and it is a softer partner to warm brass tapware than matte black is. Tied with the RZDEAL edge pulls at 4.8 stars, it is one of the two highest rated picks here, from a review base of more than eight hundred. Square handles are less forgiving of a crooked install, so this is the set where a drilling template earns its money.

Flaws but not dealbreakers

Square edges are harder on hips and pockets than rounded bars, worth a thought in a narrow galley. Oil rubbed bronze is a living finish by design, so high contact points lighten over time. If you want a permanently uniform dark handle, matte black is more predictable.

Which cabinet handles should you buy?

Match your situation to the pick rather than starting from a finish you like.

What should you look for in cabinet handles?

Start with hole centres, then pack size, then finish, in that order. Everything else is taste.

Hole centre spacing. The distance from the middle of one screw hole to the middle of the other, quoted in millimetres or inches, commonly 64mm, 96mm, 128mm, 160mm and 192mm. Measure your existing handles first: land on the same number and the swap is a screwdriver job, miss it and it becomes filling, sanding and drilling on a face that shows every mistake.

Handle length against drawer width. The rule of thumb most Australian hardware showrooms quote is that a pull should run about a third of the width of the drawer front.

Pack size. Count before you buy. A modest Australian kitchen runs roughly 15 to 25 pieces once you include the pantry, under bench doors, pan drawers and overheads, so packs of ten mean two or three, bought together to keep the finish batch consistent.

Material and finish. Solid brass is the most durable and the most expensive, and it patinas. Zinc alloy casts crisply and takes plated finishes well. Stainless steel puts a hard base under a coating, and aluminium is light and cheap. Matte black shows fingerprints and oil, satin and brushed nickel hide water marks, and warm brass needs matching against your tapware in daylight.

Projection and screw length. How far the handle stands off the door decides whether you catch a pocket on it: under 20mm is flat and low snag, over 30mm is easy to grab with wet hands. Most handles ship with screws sized for a standard 16mm to 18mm door, and Shaker doors with an applied frame need longer machine screws, almost always M4. Buy a length assortment if your doors are not standard.

If you are drilling fresh holes rather than reusing old ones, a level and a template beat a steady hand. Our spirit level guide covers the small torpedo levels that fit inside a cupboard.

How do you clean and maintain cabinet handles?

Warm water, a drop of dish soap and a soft cloth handles almost everything. Anything more aggressive is where finishes get ruined.

The rule that matters is that the finish on most cabinet hardware is a coating, not the metal itself. Matte black, oil rubbed bronze, brushed brass over aluminium and satin nickel are all applied over a zinc, aluminium or steel body. Abrasive creams, scouring pads and bleach based sprays cut through them, and a dulled patch never comes back.

Handles near a cooktop pick up an oily film plain water will not shift. A cloth wrung out in warm soapy water, worked along the grain of a brushed finish rather than across it, takes it off. Knurled handles need a soft toothbrush for the crosshatch, and cup pulls need a wipe inside the bowl. Solid brass is the exception to the coating rule: it darkens into a patina, and a brass polish brings it back. Never use brass polish on a plated finish, because you will polish through it.

Once a year, go around with a screwdriver and nip up every handle. Hardware works loose from ordinary use, and a loose handle wallows out the hole over time, a much bigger repair than a quarter turn today. In coastal homes check the screws too, because plain steel corrodes in salt air long before the handle fails.

You will also want these

A handle swap is a small job made easier by a few cheap things.

• King and Charles cabinet hardware jig for repeatable holes at the same spacing on every door, which is the difference between a straight run and a wavy one.
• Cabinet handle jig with automatic punch and drill bits if you are starting from undrilled doors and want a punch mark to stop the bit wandering off.
• WELLOCKS M4 cabinet screw assortment, 25mm to 50mm so thicker doors and Shaker profiles are covered.
• M4 x 49mm nickel fixing screws for a thick door where the supplied screws come up short.
• Scotch painter tape to mark drill positions and stop the bit skating on laminate.
• MR.SIGA microfibre cloths for the wipe down afterwards.

The competition

A few handle sets came close and did not make the cut.

The Amazon Basics modern finger drawer pull in golden champagne is a tidy 64mm handle, but it is sold as a single rather than a multi pack, which makes it awkward for a whole kitchen where you need 15 to 25 pieces.

Asidrama sells a large family of brushed brass and antique brass pulls in 96mm, 128mm and 192mm, and they are well rated. We left them out because the range splits its reviews across so many size and finish variants that it is hard to tell which pack a rating belongs to.

Malimali gold edge finger pulls cover the same handleless brief as the RZDEAL set at a lower rating, and the RZDEAL pulls are solid brass rather than plated, which is the difference that shows over a decade.

Amerock and Yetaha both sell cup pulls with large review counts. The Hestia set won on a ten piece pack, satin nickel rather than a shell shaped antique finish, and a listing that states the hole centres in both inches and millimetres.

Australian boutique makers such as Castella, Rappana and Dune also come up in these searches. They sell through their own stockists rather than Amazon Australia, so they sit outside this comparison.

Cabinet handle questions Australians ask

What size cabinet handles should I buy?

Measure the hole centres on your existing handles first, from the middle of one screw hole to the middle of the other. The common Australian sizes are 64mm, 96mm, 128mm, 160mm and 192mm, and matching your existing spacing turns the job into a screwdriver task instead of a drilling and filling one. If you are drilling fresh holes, use 128mm on drawers and 96mm or 128mm on doors as a starting point.

What is the 1/3 rule for cabinet handles?

It is the common design guideline that a handle should span roughly one third of the width of the drawer or door front it sits on. A 400mm drawer suits a handle around 128mm long, and a 900mm pan drawer wants either a long pull or two shorter ones spaced evenly. It is a rule of thumb rather than a standard, so use it to avoid handles that look obviously undersized.

Can I replace cabinet handles without drilling new holes?

Yes, as long as the new handles share the same hole centre spacing as the old ones. Measure first, then buy to that number. If you cannot match the spacing, single screw knobs will fit any door that already has one hole, and edge pulls or back plates can cover holes you would otherwise have to fill, sand and touch up.

Which cabinet handle finish is best for an Australian kitchen?

Satin nickel and brushed nickel hide fingerprints and water marks best, which suits a busy family kitchen. Matte black looks sharp on white and grey doors but shows oil spatter near a cooktop. Warm brass finishes work well with timber and darker cabinetry, and they should be matched against your tapware in daylight rather than under shop lighting.

How many cabinet handles does an average Australian kitchen need?

Most kitchens need somewhere between 15 and 25 pieces once you count under bench doors, overhead doors, pan drawers and the pantry. That means two or three packs of ten for a full swap. Buy them in a single order so the finish comes from the same production batch, because brushed and plated finishes can vary slightly between batches.

What else should you sort out while the screwdriver is out

A handle swap tends to be the first job people do in a new place, and it starts a list.

• Best drawer organisers in Australia for the inside of the drawers you just put handles on.
• Best cordless drills in Australia if you are drilling fresh holes rather than reusing old ones.
• Best screwdriver sets in Australia for a driver that will not chew ten identical screw heads.
• Best tape measures in Australia for measuring hole centres and drawer widths properly.
• Kitchen essentials checklist for everything else a first kitchen needs.
• Garage storage ideas if the cupboard run you are upgrading is in the garage.

About the author

Anish Puri founded NestPath in 2026 after going through the Australian first-home-buyer process himself. NestPath focuses on Australian first-home buyers because the existing review sites are American, generic, or both. Anish handles editorial selection across the homeowner hub. Reach out: hello@nestpath.com.au