Best Table Legs in Australia (2026)

Table legs are the cheapest way to turn something you already own into furniture you actually like. A rescued slab of timber, an old door, a benchtop offcut from a kitchen renovation: bolt four legs underneath and you have a dining table, a desk or a hall bench for a fraction of what a finished piece costs.

The catch is that table legs are sold by height and shape rather than by the job, so it is easy to order a set that looks perfect and arrives 30cm too short. This guide fixes that. We researched the replacement and DIY leg sets Australians can order on Amazon AU, pulled the heights, widths, load ratings and set sizes straight from the listings, and matched each one to the table it is actually built for. Seven sets made the cut, from a 30cm timber taper for a coffee table up to 71cm steel frames for a full dining setup.

What are the best table legs in Australia right now?

For most people building a dining table or a desk, the VEVOR 71 x 45cm Square Steel Table Legs are the set to buy. They are the right height straight out of the box, they carry a published load figure of 453.6kg for the pair, and they come with threaded levelling cups so you can take the wobble out of an uneven floor without shimming anything under the feet.

If your project is lower to the ground, the Artiss 40 x 30cm Metal Table Legs are the Australian brand answer. That 40cm height is coffee table and hall bench territory, the tube is a chunky 75mm wide, and the pair is rated to 200kg. On a budget, the VEVOR 76.2cm Hairpin Table Legs give you four legs rather than two, in the mid century shape that suits a slab top, for the least money of any set here.

Table legs compared at a glance

Heights below are the leg height only, so add the thickness of your tabletop to work out where the surface will finish.

How we chose these table legs

Most leg guides you will find are written for American workshops, where the standard finished dining height and the bolt threads are both different to ours. We built this list around the number that decides whether your table works: the finished height once your top is on. Australian dining chairs are usually built around a seat about 45cm off the floor, which wants a finished surface near 74cm, and a benchtop offcut is often 32mm to 40mm thick. That is why the 71cm sets sit at the top of this guide and the 76.2cm sets are pitched at thinner desk tops. We also gave weight to levelling feet, because a lot of Australian homes pair tile or floating floorboards with slabs that are not perfectly flat, and a leg that cannot be trimmed at the foot will rock forever.

• We started from the replacement and DIY table leg sets Australians can order on Amazon AU, and cut anything that was really a sofa foot, a cabinet riser or a floor protector.
• Star ratings, review counts and prices were checked fresh on the day this guide was written, from the listing itself.
• Heights, widths, load figures, materials and set sizes are quoted from the listing specifications rather than estimated by us.
• Where two sets were close, we favoured the one with a published load figure, adjustable feet and a powder coated finish that copes with a humid garage.

Best table legs overall: VEVOR 71 x 45cm square steel legs

These are the legs to buy if you are building a dining table or a solid work table and you want the height decision made for you. They stand 71cm tall and 45cm wide, so a top of 20mm to 40mm lands you at roughly 73cm to 75cm, which is where an ordinary dining chair wants to sit.

The build is carbon steel in a powder coated black finish, sold as a set of two frames, with a published maximum load of 453.6kg. The shape is a simple square section box, the least fussy of the industrial looks. The top plates are pre-drilled, so fixing them to a slab is a matter of marking through the holes and driving screws.

What lifts this set above the other 71cm frames is the hardware in the box. You get four adjustable M10 levelling cups with hexagonal nuts and an open ended wrench, plus 18 self tapping screws. That means you can true the table up on the spot instead of hunting for cardboard shims, and you are not making a second trip for fixings. It shares the highest star rating in this guide at 4.7, alongside the Artiss and the Y-CFHFC trapezoid.

One thing to read carefully: despite the listing calling them adjustable, the leg itself is not telescopic. The listing states plainly that it is not extendable. The adjustment is in the threaded foot cups, which give you a few millimetres of levelling range, not a change of table height. If you need a genuinely variable height, you are shopping for a sit stand frame instead of a fixed leg.

Flaws but not dealbreakers

The word adjustable in the title oversells what the feet do. It is also a set of two, so a very long top will want a centre rail or a third frame to stop the middle sagging, and the black powder coat shows fingerprints until you wipe it down.

Best table legs for a bench or coffee table: Artiss 40 x 30cm metal legs

Artiss is an Australian furniture brand, and this is the set we would put under a hall bench, a coffee table or a low media unit. At 40cm tall and 30cm long it is squarely coffee table height, and the rectangular box frame gives a low top the visual weight it needs so it does not look like a shelf on stilts.

The listing specifies iron construction with a 75mm wide tube, a top steel plate of 75mm by 4mm and a tube thickness of 75mm by 25mm. Weight capacity is quoted at 200kg for the pair. The frames are fully welded rather than bolted together, which is the difference between a bench that stays square and one that develops a lean after a year of use.

The finish is a matt black powder coat described as rust resistant, and Artiss includes four non slip feet pads in the box to protect floorboards and stop the frames sliding on tile. Pre-drilled holes in the top plate make the fix straightforward. It shares the highest rating here at 4.7 with the VEVOR square set and the Y-CFHFC trapezoid.

The one genuine annoyance is that screws are not included. The listing says so directly. Order a box of wood screws at the same time and you will not lose a weekend to it.

Flaws but not dealbreakers

No screws in the box, and no levelling feet either, so an uneven tile floor will need felt or rubber under one corner. At 40cm it is also too low for anything you plan to eat dinner at.

Best budget table legs: VEVOR 76.2cm hairpin legs

Hairpin legs are the cheapest way to make a slab of timber look like mid century furniture, and this VEVOR set is the one most Australians end up buying. It is the cheapest set in this guide, and the most reviewed of our picks, with 3,965 ratings behind a 4.6 average.

You get four legs rather than two, each 76.2cm tall (30 inch). On a 20mm top that finishes around 78cm, so it is better suited to a desk or a console than a dining table where chairs need clearance. Construction is carbon steel with a powder coating, in the three rod hairpin shape, and each leg weighs a shade over 600 grams so the whole set is 2.46kg.

The load figure quoted on the listing is about 100kg per leg (220 lb). That is a maker rating for the leg on its own rather than a verdict on the table you build, and a hairpin carries its load through a thin rod rather than a box section. Rubber floor feet and a screw kit are both included, which is unusual at this price and saves the trip that the Artiss set costs you.

Hairpins are also the friendliest legs for a first build. There is no frame to square up: you sit each leg in a corner, mark three holes, drive three screws, and the job is done in under half an hour.

Flaws but not dealbreakers

The three rod hairpin flexes slightly side to side under a heavy top, and at 76.2cm it is taller than dining height. The powder coat is also thin enough to chip if you drop a leg on concrete, so fit them last.

Best white table legs for a light room: Y-CFHFC 40.6cm trapezoid legs

Almost every table leg sold online is black, which is a problem if your room is white oak and pale linen. This Y-CFHFC set is a genuine white powder coated trapezoid, and it disappears under a light top in a way a black frame never will.

It is a set of two, 40.6cm tall and roughly 27cm deep (16 inch). That puts it in coffee table, bench and TV unit territory. The listing quotes a maximum weight capacity of about 363kg (800 lb), and the pair weighs 1.36kg so it is easy to handle on your own while you mark the holes.

The trapezoid shape earns its place. Because the foot is wider than the top plate, the load spreads outward and a narrow top feels far more planted than it does on straight legs. It is the shape to choose if the table will live in a walkway and take the occasional knee.

Four adjustment feet pads and screws are included, so this is a complete kit. Along with the VEVOR square set and the Artiss frames, it shares the highest star rating in this guide at 4.7.

Flaws but not dealbreakers

White shows scuffs from shoes and vacuum heads, and touch up paint that matches a factory powder coat is hard to find. At 40.6cm it is also a low table leg only, so do not order it hoping to build a desk.

Best timber table legs: La Vane 30cm solid wood tapered legs

If your house leans warm and mid century rather than industrial, steel is the wrong answer. This La Vane four pack is the only timber option among our picks, and a tapered wooden leg under a plywood or oak top reads as furniture rather than as a project.

Each leg is 30cm (12 inch), making this the shortest set in this guide. That is coffee table, low bench and platform bed territory. The four legs together weigh 1.84kg and the listing describes a classic tapered form in solid wood with a clear finish.

The important detail is the thread. La Vane supplies a 5/16 inch bolt for the American market and M8 for everyone else, and the two are close enough in size to look interchangeable while having incompatible thread pitches. If you already have angled or straight mounting plates on hand, measure before you fit. If you do not, use the mounting plates in the box, because they are matched to the supplied bolts and take the guesswork out.

What you get for that is the easiest leg to change your mind about. Because they thread into a plate, you can unscrew all four, flat pack the table for a move, and screw them back in at the other end. Anyone renting and moving every couple of years will appreciate that more than a welded steel frame.

Flaws but not dealbreakers

The listing does not publish a load figure, so treat these as legs for lighter tops rather than a slab. The thread standard also catches people out, and a threaded timber leg will loosen over time if the table gets dragged around, so check the fixings once a season.

Best legs for a low coffee table or bench: Osring 35.6cm U-shaped table legs

A low top wants a low, wide leg, and the U shape is the simplest way to get one. This Osring set is a pair of solid steel U-shaped legs in black, sized for coffee tables, TV stands and benches, so the frame reads as two clean lines under the top rather than four posts.

The pair stands 35.6cm tall (14 inch), which is coffee table and bench height rather than dining or desk height, and the listing describes the legs as solid steel with a black finish. It carries a 4.3 average rating from 274 ratings, a fair body of feedback for a shape this specific.

A U-shaped leg has one practical advantage over a single post at each corner: the flat bar along the floor spreads the weight, so the frame sits more evenly on a rug or a slightly uneven floor, and there is nothing to catch a toe or a vacuum head in the middle of a walkway.

Flaws but not dealbreakers

At 35.6cm this pair only suits low furniture, so it is not the answer for a side table you eat at or a desk. A U leg also needs a top at least as wide as the U, so measure the top before you order, and a matte black finish shows dust on the flat bar sooner than a polished leg does.

Best table legs for a desk: VEVOR 76.2cm steel desk legs

A desk asks different questions to a dining table. You want four corners so there is no centre rail fighting your knees, you want a decent load figure because monitors and a mechanical keyboard add up, and you want to be able to level it on a floating floor. This VEVOR set answers all three.

It is a set of four cylindrical carbon steel legs, each 76.2cm tall (30 inch), in a matte black finish. The listing quotes a maximum load of roughly 544kg (1,200 lb), which is the highest published load figure of any pick in this guide. The set weighs 5.9kg, so these are noticeably more substantial in the hand than a hairpin.

The hardware is the reason it is here. Four adjustable M10 leg cups with hexagonal nuts let you dial out a rocking desk, and you also get four M8 machine screws and 22 self tapping screws, so you can fix to a solid top or to a plate. On a floating timber floor, where a desk that rocks under your elbows becomes maddening within a week, that levelling range does real work.

It has the fewest reviews of our picks at 117 and a 4.4 average, which is worth knowing, though the specification and the included hardware are the strongest here for a desk build.

Flaws but not dealbreakers

The smallest review count in this guide. Four cylindrical legs also need more careful marking than two frames, because any error shows up as a rock rather than a lean.

Which table legs should you buy?

Find the sentence that matches your project and start there.

What should you look for in table legs?

Height first, then load, then how the leg meets the top. Everything else is taste.

How do you work out the right leg height?

Take the finished height you want and subtract the thickness of your top. A dining table usually wants to finish near 74cm, so a 32mm benchtop offcut needs legs close to 71cm. A desk is comfortable anywhere from 72cm to 76cm depending on your chair. A coffee table sits between 40cm and 45cm, and a hall bench around 45cm. Measure the top with something you trust rather than guessing, because a 10mm error is the difference between comfortable and cramped. If your tape measure has seen better days, replace it before you start marking.

How thick should the leg be?

Thicker tube looks heavier and resists side to side racking better. The Artiss frames use a 75mm wide tube, which is chunky and suits a solid top. A three rod hairpin is the opposite: visually light, quick to fit, and fine under 20mm to 30mm tops but flexible under a slab. Match the visual weight of the leg to the thickness of the top and the table will look right even before you fuss over the finish.

What about mounting and load figures?

Most steel legs come with a pre-drilled top plate, so you mark through the holes and drive screws. Timber legs usually thread into a plate instead, which means you can unscrew them for a move. Load figures on listings are quoted for the whole set on some products and per leg on others, so read the wording before you compare two numbers. Every one of those figures is a maker rating for the legs on their own, and what a finished table carries is decided by the top and the fixings you drive into it, so build for what will sit on the surface and never treat a home built table as something to sit or stand on. If you are joining boards to make your own top first, a pocket hole jig is the shortcut most first timers wish they had bought earlier.

Do you need levelling feet?

In an Australian home, usually yes. Tile, floating floorboards and older hardwood are rarely dead flat, and a table on four rigid feet will find the high spot and rock on it. Threaded levelling cups let you wind one foot down a few millimetres and be done. If your chosen legs do not have them, rubber shims or stick on felt do the same job for very little.

How do you look after table legs?

Very little, but the little there is matters.

Check the fixings twice a year

Every table gets dragged at some point, and every drag works the screws in the top plate a fraction looser. Twice a year, tip the table on its side and nip up each screw. Threaded timber legs deserve more attention than bolted steel frames, because a leg that unwinds a quarter turn will start to rock long before it looks loose.

Keep the coating intact

Powder coating is tough but not invincible. Wipe steel legs with a dry cloth, which is what these listings recommend, and use a barely damp cloth with a little dish soap for anything sticky. Avoid abrasive pads and solvent based cleaners, because a scratch in the coating on a leg that lives near a wet area is where corrosion starts.

Protect the floor and the feet

Stick felt under every foot on timber floors and rubber on tile. It saves the floorboards, it stops the sliding noise, and it keeps grit off the underside of the leg.

You'll also want

Legs are rarely the whole shopping list. These are the small things that decide whether the build takes an afternoon or a weekend.

• Mr. Pen Wood Screws Assortment Kit, because several leg sets ship without screws and a mixed kit means you can pick a length that will not punch through a 32mm top.
• Glarks Self Drilling and Self Tapping Screw Kit for fixing steel top plates where a plain wood screw will not bite.
• Bosch 60cm Spirit Level to check the top before you blame the legs, and again after you fit them.
• Amazon Basics Round Felt Furniture Pads for timber floors, so the finished table does not score the boards on its first move.
• X-Protector Furniture Levelers if your legs have no adjustable feet and the floor has a high spot.
• X-Protector Non-Slip Furniture Pads for tile and polished concrete, where a table that slides is more annoying than one that rocks.

The competition

Plenty of good leg sets did not make the list, and it is worth saying why.

The OIKITURE 71 x 50cm Rectangle Table Legs are a solid Australian branded dining frame and were close to a pick, but with only 13 ratings behind them there is not enough feedback yet to judge how they hold up, and they are the dearest option we looked at in that shape. The VEVOR 71cm X frame Steel Table Legs are handsome, with a 79mm square box section, but they carry the lowest average rating of any dining height set we compared.

Artiss also sells the same frame family we picked in a 71cm dining height, and if you want the Artiss look at dining height rather than bench height, that is the size to search for.

We also passed over the many wooden bun feet and sofa risers that turn up when you search for table legs. They are furniture feet rather than table legs, and a 5cm bun under a dining top will not do what you want. If you are shopping for a portable folding surface instead of building a fixed table, our trestle table guide is the better starting point.

Table legs FAQ

How tall should table legs be for a dining table?

Aim for a finished height near 74cm, then subtract the thickness of your top to get the leg height. A 32mm benchtop offcut wants legs around 71cm, and a 40mm slab wants legs closer to 70cm. Most Australian dining chairs are built around a seat about 45cm off the floor, which is why 74cm feels right and 78cm feels tall.

Do you need two table legs or four?

Two frames look cleaner and keep the corners free for chairs, while four individual legs are easier to fit and easier to level. Choose two frames for a dining table where people sit down the sides, and four legs for a desk where a centre rail would hit your knees. A long top on two frames is worth bracing with a centre rail underneath to stop the middle sagging.

Are metal or timber table legs better?

Metal legs carry more weight for their size and come with published load figures, which makes them the more predictable choice under a heavy slab. Timber legs suit warmer and more traditional rooms, take stain or oil so you can match them to your top, and unscrew from a mounting plate so the table flat packs for a move. The right answer is usually decided by the room rather than by the engineering.

How thick should table legs be?

Match the visual weight of the leg to the thickness of the top. A chunky 75mm box section suits a solid timber slab, while a three rod hairpin looks correct under a 20mm to 30mm top and starts to look flimsy under anything thicker. Thicker tube also resists side to side racking better, so wider frames are the sensible choice for a long dining table.

Will table legs work on a timber slab top?

Yes, provided you fix them in a way that lets the slab move. Solid timber expands and contracts across its width with humidity, so fixing a rigid steel frame tight through round holes in both directions can cause the top to split over time. Use slotted holes or figure eight fasteners across the width of the slab, and keep the fixed points near the centre so the timber can move outward.

Build out the rest of the workshop

A table build is usually the first project, not the last. These guides cover the tools and the furniture that tend to follow it.

• Best cordless drills in Australia for the pilot holes every one of these leg sets needs.
• Best spirit levels in Australia to check the top and the floor before you blame the legs.
• Best orbital sanders in Australia for getting a rescued benchtop ready to finish.
• Best sawhorses in Australia so you are not working on the lounge room floor.
• Best workbenches in Australia for the garage setup that makes the next build easier.
• Best dining chairs in Australia to match seat height to the table you just built.

About the author

Anish Puri founded NestPath in 2026 after going through the Australian first-home-buyer process himself. NestPath focuses on Australian first-home buyers because the existing review sites are American, generic, or both. Anish handles editorial selection across the homeowner hub. Reach out: hello@nestpath.com.au